How to dispose of a well pressure tank is mostly a matter of making it safe and empty. Most residential well tanks are steel shells with a rubber diaphragm or bladder inside and a pressurized air charge, often around 28 to 40 psi. Once you shut off the pump, drain the water, and release the air through the Schrader valve on top, the tank is just scrap metal. Steel tanks go to a scrap yard or a transfer station metal pile. Composite or fiberglass tanks go with bulky waste.
Make it safe first
- Turn off power to the well pump at the breaker.
- Open a faucet to relieve system pressure.
- Close valves to isolate the tank, then drain it through the drain valve or tank tee into a bucket or floor drain.
- Release the air charge. Press the pin in the Schrader valve on top of the tank, like letting air out of a tire, until it stops hissing.
- Disconnect the tank from the tank tee once it is empty and depressurized.
Never cut, drill, or crush a tank that still holds an air charge. The stored pressure can make a damaged tank dangerous.
Why tanks fail
A waterlogged tank, where the bladder ruptures and the tank fills with water, makes the pump short-cycle on and off. You may notice rapid clicking at the pressure switch or water spitting from the air valve. Replacing the tank is common every 10 to 20 years. If the old tank is still sound and just lost its air charge, re-pressurizing it may help before you replace it.
Steel tanks: scrap metal
Most well tanks are painted steel. Scrap yards accept them, especially once you note they are depressurized and empty. Some yards ask you to remove the plastic base or cut a hole to prove it is open, but only a yard employee or someone with the right tools should do that, and only after the air is released. Transfer stations often take tanks free or for a small fee in the metal area. See separating metal before it is buried.
Composite tanks
Fiberglass and composite tanks are lighter and do not rust. They usually go in general waste or bulky waste. Some sites ask that they be cut up.
Weight and handling
| Tank size | Approx. empty weight |
|---|---|
| 20 gallon | 25 to 40 lb |
| 32 to 44 gallon | 45 to 70 lb |
| 80 to 119 gallon | 80 to 130 lb |
An empty tank is bulky but manageable for one person on a dolly. A tank still holding water can weigh hundreds of pounds, so drain it fully before moving.
Contractor removal
If a well contractor or plumber installs the new tank, removal of the old one is usually included or available for a small fee. They often take it to scrap themselves.
Related well and water parts
Old pressure switches, gauges, and fittings can go in the scrap metal bin with the tank. Brass fittings are worth separating. Water softeners and treatment tanks are different; see retiring a water softener.
Lead and older fittings
Some older tank tees and fittings contain lead in the brass. Wash your hands after handling them, and recycle them with scrap brass rather than the trash.
How to dispose of a well pressure tank FAQ
Can I put a well pressure tank in the trash?
Usually not. Steel tanks go to scrap metal; composite tanks may go to bulky waste.
How do I release the air from a well tank?
Press the pin in the Schrader valve on top until the hissing stops, after draining the water.
Is a well pressure tank worth anything as scrap?
A small amount. It is mostly steel, so it brings low scrap prices.
Do scrap yards take well tanks?
Most do if the tank is empty and depressurized. Some ask that it be opened.
How long does a well pressure tank last?
Often 10 to 20 years, depending on water quality and how often the pump cycles.
The bottom line
How to dispose of a well pressure tank: shut off the pump, drain the tank, release the air charge at the valve, and disconnect it. Steel tanks go to a scrap yard or transfer station metal pile; composite tanks go to bulky waste. Never cut a tank that still holds pressure. Use the map to find a site near you that takes scrap metal.
Guides and tools
Appliance disposal guide · Dump cost calculator · All material guides